Products

Grech CPA15000 Auto Cleaning Pressurized Koi Pond Filters (15000 L/H) New pond filter generation: Bio pressure pond filter CPA-15000 Characteristics: Indicator for pollution High flow rate Optimum development of biological pond filter Easy and uncomplicated bio-pressure pond filter-system This system provides fast and reliably clear water Easy backwashing (by flipping a switch) Different filter materials (special filter foams) Advantages: Mechanical and biological pressure filter with integrated UVC-clarifier. All connections and technology are in the lid/cover, the filter can be buried to lid for concealment without difficulty. Flush back function with maintenance indicator. Cleaning and maintenance: The water can be pumped to a higher lying waterfall and then led back into the pond. The annual maintenance is limited to checking the filter media and the UV-lamp. The filter has a modern flush back function that can be adjusted by means of a switch with four functions. With the switch you have the following possibilities for setting: The EasyClean flush back function: • Switch position "Filter" Normal operation - the water passes through the pressure pond filter with the help of a pond pump and returns cleanly into the pond. • Switch position "Clean" Cleaning mode - By turning the switch the motor that is integrated in the top of the filter is switched on and makes the filter sponges rotate in the inner of the pond filter and cleans them from the coarse dirt without opening the pond filter. During the cleaning operation the dirty water is drained by an additional connection and can be used for example for garden irrigation. Filter Placement: The filter is placed at the pond side and by means of a a suitable pump (not included in delivery) connected with the water. The water circulates through the filter and the UV-device and after being cleaned is led again into the pond. Fundamental Functionality: Pond filter combine the mechanical and biological cleaning. Microorganisms settle on the filter material and remove germs and bacteria from the water. By mechanical filtering, suspended particles and dirt remain in the pond filter and by this means no longer return to the pond water. It takes about 4-6 weeks, until Filter Bacteria have sufficiently colonized the bio pond filter. Only thereafter t is advisable to switch on a UVC Pond Clarifier. Starter bacteria help to shorten the start-up phase of a new filter. Starter bacteria refer to microorganisms especially grown in a laboratory. By adding them, you can shorten the start-up phase considerably. Bacteria are active above a temperature of approximately 10°-12°C, the pond filter´s temperature should exceed 40°C. So the pond filter should be placed in the shadow and not be exposed to direct sunlight. UVC-pond clarifiers irradiate the water in a flow-through reactor with UV rays. The UV-C radiation destroys the swimming algae. The algae agglutinate to large particles and ca be easily removed by means of mechanical filtering. Our UVC clarifiers modify the tertiary and the quaternary structure of the algae proteins by means of UV-radiation. This means the destructions of the algae which can be removed from the water by pond filters.

Cluster Jet nozzles produces a vertical columns of water using connection rows of clear stream jet giving the appearance of a large diameter water columns. Due to the refractive quality of the individual streams, jet cluster nozzles offer good visibility at the long range viewing distance. Nozzle is further enhanced when combined with submersible lighting. Applications include indoor or shielded outdoor use in commercial, institutional, municipal building and landscape projects, as a primary display features, or as peripheral accents to primary display features they are also used effectively in series or grouped in clusters.

Swimming Pool LED driver used for individual LED lamp of 14.4Watts / 13 VDC configuration. Used for Underwater LED lights for pools / water bodies.

SunSun HW 5000 Canister Filter The HW-5000 features a removable DC pump with SINE wave technology- more energy efficient than regular canister pumps. Includes a Smart Digital Controller that allows users to adjust the water flow rate and UV sterilizer's "ON" time. The ceramic impeller is more durable and can be used with freshwater and saltwater aquariums. The HW-5000 also includes 3 media baskets that are easy to clean. Big media baskets provide users the ability to add large amount of different filter media which is not included with the filter. Bottom drain hole with valve allow for easy maintenance of canister. Easy to start, no priming necessary, simply add water and turn on the power. An adjustable tube holder can be mount on the aquarium with a 7/8" rim and can be remove for aquarium with larger rim. Bottom drain hole with valve allow for easy maintenance of canister. Easy to start, no priming necessary, simply a water and turn on the power.

Ring Blowers are designed for the conveying of air as well as for generating pressure or vacuum. Industrial Ring Blowers are known by many different names across the world. They are also referred to as Regenerative Blower, Side Channel Blower, Turbine Blower, Ring Compressor, Industrial Vacuum Blowers, Vortex Blower etc. Industrial Ring blowers are manufactured for both pressure and vacuum service. When a ring blower is used for pressure, it is usually configured for use as air supply units or compressors, while vacuum blowers are frequently used as vacuum pumps or fume/dust exhausters. All regenerative ring blowers consist of an impeller that spins within a housing. This housing contains both an intake channel and an outboard channel; hence the name side channel blowers. When the impeller moves past the intake port, air is drawn in and trapped between the impeller blades. As the impeller continues to turn, the air is pushed both inward and outward through both channels, and this process continues until the impeller stops rotating. It is this regenerative process that allows the side channel blower to function as both a pressure blower and a vacuum blower. While the air trapped between two impeller blades represents only a small pressure increase, the sum total of the blades, from intake to outlet, is capable of powerful continuous operating pressures. Below are some of the applications of Industrial Ring Blowers / Side Channel Blowers. Aeration Effluent treatment plant (ETP) Sewage treatment plant (STP) Aquaculture Pneumatic conveying Automatic looms Automatic bottling machines Vacuum table Plating tank agitation Hopper agitation Jacuzzis Dental and other medical suction Industrial sewing machine Sock loom Furnace air intake Features Rugged & Reliable: The impeller shaft and casing are Aluminum cast. Side Channel Blowers are built tough for continuous 24-hour operation. Minimal Lubrication Required: The rotating parts of Industrial Ring Vacuum Blowers are not in contact with the casing. There is, therefore, no friction during operation and thus no internal lubrication is necessary. Only the bearings need occasional lubrication after many hours of operation. Low Noise Level: These are direct drive units with integral silencers, which ensures low noise levels. Cleaning: When dust or residue is evident, clean the entire surface of the ring blower Lubrication: After approximately 20,000 hours of operation or 18 months, replace the grease in the bearings

Eight Head Atomizer The ultrasonic atomizer uses electronic high-frequency oscillation (the oscillation frequency is1.7MHz or 2.4MHz, which is beyond the range of human hearing, and the electronic oscillation isn't harmful to humans and animals), through the high-frequency resonance of the ceramic atomizer, to remove the liquid water break up the molecular structure of natural flowing mist generated, without additional heat or addition of any chemicals. High-quality material: This product uses high thermal conductivity, high corrosion resistance, high-quality 304 stainless steel; the nozzle adopts copper wafers, which has strong heat dissipation capacity and low loss; it will not rust and has a longer service life. Protection function: Water shortage protection, when the water level is lower than the induction capacitor, the power will be automatically turned off. The built-in water temperature sensor will automatically turn off the power when the water temperature is 55°C. High safety, no need to worry about potential dangers. Very safe to use. High-quality nozzle: The nozzle is designed independently, and the current of each nozzle is automatically adjusted electronically. When a single nozzle is damaged, other nozzles can work normally. Widely used: 8-head ultrasonic atomizer, which can be used for stage atomization and various gardening applications, including hydroponics, breeding, greenhouse flower humidification, viewing platforms, etc. The mist generator/fog generator uses ultrasonic electronic technology to turn water molecules into mist-like molecules, which is very suitable for use in your pond, botanical garden, rockery, fish tank, vase, swimming pool, etc. It will create a magical atmosphere, and when you use this fog generator, you will find a lot of fun. Shell material: 304 stainless steel Nozzle material: Copper Working voltage: DC 42V-48V Working Current: 4.1A-4.7A Output power: 200W Spray volume: 5 KG / H Cooling method: air cooling The best working water level: 6~7cm Precautions for the use of eight-head atomizer 1. When using this 8-head atomizer, please select the matching transformer whose output voltage is AC36V. 2. When multiple 8-head atomizers are used in the same container, the shells of the atomizers must be connected to each other to prevent electrical corrosion of the shells. 3. This atomizer is suitable for atomizing neutral liquids (PH value 5~8). Acidic liquids will corrode the shell and atomizing film, and alkaline liquids will affect the amount of atomization, reducing the 8 atomizers and The life of the atomizer sheet, and cause the water level switch to fail and damage the atomizer. 4. Please do not damage the water level switch during the installation process, so as to avoid the failure of the water level switch and cause the atomizer to lose control. Stop using the water level switch if it is damaged, otherwise the atomizer sheet will burn dry and further damage the atomizer. At this time, it can be used after being repaired by professional maintenance personnel. 5. When the atomizer is working normally, please do not put your hands on the spray cavity of the atomizer to prevent ultrasonic damage. 6. The atomizer must be in water to work normally. Please put it in the water before turning on the power, and make sure that the surface of the atomizer is in a state of water to avoid damage to the atomizer. 7. When you stop using the atomizer, please disconnect the switch power first, and then take out the atomizer from the water. Maintenance and maintenance of eight-head ultrasonic humidifier In order for your product to achieve the longest service life and best use effect, please read the following carefully. 1. After the atomizer has been working for a long time, scale will be deposited on the shell and the surface of the atomizing sheet, which will seriously affect its service life and atomization volume. Therefore, it is recommended to clean the atomizer at least every half a month. When cleaning, use a soft cloth moistened with alcohol to gently wipe the surface of the atomizer shell and the atomizer sheet. Do not clean the atomizer sheet with hard objects to avoid scratching the atomizer sheet. 2. Water quality will affect the service life of the atomizer. Clean water is recommended. 3. After the atomizer has been working for a long time (about 3000 hours), the life of the atomizer will be attenuated and the amount of atomization will be reduced. At this time, you can replace the atomizer. Please contact the distributor for the atomizer and supporting tool keys. Business or our company. The detailed description of the replacement steps is as follows: Cut off the power, take the atomizer out of the water, and put it upside down for a while. After the water in the atomizer has all flowed out, wipe the water on the spray cavity and the inner surface of the atomizer with a dry cloth. Then use the tool spoon to unscrew the pressure ring counterclockwise, remove the old transducer, and keep the cavity of the atomized transducer dry and clean. Install the new transducer with the front face up and the reverse face down, and turn the pressure ring clockwise.

Fish Farming Pumps for Biofloc Fish Tanks and Biofolc Ponds Product description Hailea HAP-120 & HAP-200 Hi-Blow Air Pump consists of advanced air-compressing system, with sound damping and multilevel muffler for extremely low in noise level. Special artificial rubber to keep a steady air output and pressure. Advanced air-compressing system, damping system and multilevel muffler which is extremely low in noise. The structure is reasonable and compact, it is long service life and acquiring best effect with lowest energy consumption. Aluminum alloy case, quick in heat-dissipation and easy to move. Why Air Blower For Fish Farming is needed? Air blowers are one of the other required equipment. Without using fish farming pump in a Biofloc Fish Farming Tank we can not control toxic stuff like Ammonia and if fishes are kept in high density they will face low Oxygen issue. As fishes grow they require more Oxygen and to fulfill that requirement we need a good quality Fish Farming Pump so that we can meet with the required Oxygen level all the time. If any given time Oxygen level goes down we may start facing mortality. And due to Low oxygen, fishes face stress and it affects their growth rate. In any Biofloc tank there will be “Floc” too along with fishes and it will also require sufficient Oxygen to stay alive and play its role in controlling ammonia and converting sludge into single cell protein, which is consumed by fishes as food. Air Pumps for Biofloc Fish Farming Tanks 1- Helps in maintaining Oxygen 2- Control ph 3- Helps in controlling ammonia 4- and Helps controlling somewhat temp too

Stainless Steel Waterfalls are a simple solution to creating a waterfall or water shoot in your garden. Made from high quality stainless steel they allow a single hose to supply water which is then internally baffled to create an even sheet of water. To increase the ease of installation these waterfalls have a connection at the bottom, so one can be fitted with a connection hose tail. We suggest the largest size pipe that your pump can accept should be used. As with all waterfalls the flowrate required to ensure that the sheet is still wide enough when it hits the surface of the pond / reservoir is determined by both the width of waterfall and the installation height. Stainless Steel Waterfalls Features • High quality 304 grade stainless steel • Single hose connection. • Back or bottom connection position • 50mm deep lip • Can be wall mounted • 2 year guarantee

An almost limitless range of interesting effects and patterns can be achieved with our Comet nozzle. Used as a single jet, or in groups, or in concert with other nozzle models, the Comet’s single, clear stream, glass-like effect can easily be configured to spray inward from the perimeter, or outward from center, and is most often incorporated into spray rings and bars.

Overview of the twelve-head atomizer 1. The 12-head atomization film produces an atomization effect by vibrating 1700KHZ up and down 2. Maximum temperature control of the atomizer is 55±3° and it will automatically stop working 3. The atomizer water column represents the use of a capacitor. In an environment with better water quality, it is recommended to use a steel water column atomizer. The steel water column will automatically feel the operation when the surrounding capacitance is relatively high. An environment with more scale will cause Scale builds up around the water column, causing the atomizer to fail to work. For water with a lot of scale, a steel float atomizer is recommended. The steel float works up and down mechanically. It can also operate normally in an environment with a lot of scale. 4. When the12 heads atomizer is out of water, there is a possibility that it will burn out immediately, which is dry burning. 5. The use of one atomizer will cause the temperature to rise about 3°, two will rise to 4°, and three will rise to 5°. The use of 20 atomizers at the same time needs to consider heat dissipation. PRODUCT DESCRIPTION The spray head of the atomizer is airtight and has good heat dissipation performance The circuit has stable current and pressure, over temperature, protection of water shortage, noise reduction treatment, Silent design of the product, high humidity fog, high performance. Fully enclosed design with high waterproof and dustproof function, it is very convenient to detect before the humidifier production. The built-in temperature protection induction switch is set to operate safely and reliably.Strong structure and convenient installation. Anti-scale design, users can easily replace the atomizing piezo ceramic, All stainless steel case, nickel cadmium plating, good heat dissipation. Built-in water shortage protection function. Applicable to industrial humidification, agriculture, landscape fog and so on

Submersible LED focus lights available from 3Watts up to 36Watts. Suitable for all types of ornamental fountains for residential or commercial application. Power LEDs produce bright and dynamic illumination. RGB colour changing options available on select models.

Water bells are the fountain effect producing the least noise. The relaxing sound of splashing water is particularly effective in water gardens, reception halls, or outdoor pools that are protected from wind. The Lava bell forms a closed water veil that can be attractively staged with underwater illumination.